Search found 43 matches

by Jshannon3
Fri Apr 26, 2019 12:34 am
Forum: JVM Tubes - Choice and Preferences
Topic: Looking at upgrading tubes, not sure what to buy?
Replies: 9
Views: 387

Re: Looking at upgrading tubes, not sure what to buy?

Cool thanks guys, that's what I needed to hear, buy tubes that work, don't fall for the crazy, overly priced tubes. Any recommendations????? I've heard groove tubes are reasonably priced tubes.
by Jshannon3
Thu Apr 25, 2019 1:25 pm
Forum: JVM Tubes - Choice and Preferences
Topic: Looking at upgrading tubes, not sure what to buy?
Replies: 9
Views: 387

Looking at upgrading tubes, not sure what to buy?

Has anyone done business with thetubestore.com? I'm looking at their ultimate tube upgrade for my JVM410H. I get matched EL34 power tubes(4)SED EL34 WINGED C and 5 matched and balanced pre-amp tubes GE-12AX7 JAN GE 12AX7 WA. Well its their ultimate package and it runs $689.55, Is it worth it to drop...
by Jshannon3
Thu Apr 25, 2019 12:54 pm
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: BOSS NS2 and other equipment
Replies: 2
Views: 141

BOSS NS2 and other equipment

I just bought the Boss NS2 Noise Suppressor for my JVM410H, I've tried it out in front of the signal chain, and in the fx loop, and found that it works better out in front of the signal chain along with the wah, compressor, and tuner. Has anyone else had these results, I wire, from the guitar, the w...
by Jshannon3
Sun Feb 17, 2019 9:54 pm
Forum: Guitars & Pickups
Topic: When do you call your 9 volt battery for your active pick-ups dead?
Replies: 5
Views: 1344

Re: When do you call your 9 volt battery for your active pick-ups dead?

Update: I just did my 3 month maintenance to my number 2 ESP E2 M2 Urban Camo Guitar in which I installed new Procell 9V Battery in back in December, I took a voltage reading and it had 8.94 volts, which is excellent for 3 months worth of use. I’ve been to the studio, practices, and played a lot at ...
by Jshannon3
Thu Feb 14, 2019 10:48 am
Forum: Guitars & Pickups
Topic: When do you call your 9 volt battery for your active pick-ups dead?
Replies: 5
Views: 1344

When do you call your 9 volt battery for your active pick-ups dead?

So when do you replace your battery for your pickups? Wait til the middle of a show and your sound craps out due to poor maintenance on your guitar? I’ve been reading up on this and the consensus says the 9 volt battery starts to go dead at 80% of its voltage capacity, that’s 7.2 volts. I guess you ...
by Jshannon3
Sat Feb 09, 2019 4:41 am
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: Can Pedal power supplies cause noise in the signal
Replies: 3
Views: 244

Re: Can Pedal power supplies cause noise in the signal

Update: The sound was coming from the daisy chain pedal supply chord, once I changed that everything changed. There must have been a short in the cable, I’ll have to hook up my handy dandy megger to it and check it, but once I swapped for a new one”poof’ noise gone. Now I can start putting pedals ba...
by Jshannon3
Sun Feb 03, 2019 6:11 pm
Forum: Guitars & Pickups
Topic: Floyd Rose’s noiseless springs
Replies: 7
Views: 449

Re: Floyd Rose’s noiseless springs

Update: one thing I do notice on guitar #1, the guitar with the noiseless springs, is that when you make a quick stop while playing, it’s utter silence. No ringing, no humming, no machine noise, nothing. On guitar # 2, which is still stock, you have that little bit of machine noise, ringing when you...
by Jshannon3
Sun Feb 03, 2019 12:54 am
Forum: Guitars & Pickups
Topic: Floyd Rose’s noiseless springs
Replies: 7
Views: 449

Re: Floyd Rose’s noiseless springs

Update: I burned the money(16.99) and bought the noiseless springs from Floyd Rose. Installation was easy just used my handy dandy multi tool Gerber pliers to remove the old springs one at a time and install a new one in its place. Be prepared to make a few adjustments when installing new springs ca...
by Jshannon3
Tue Jan 29, 2019 7:00 am
Forum: Guitars & Pickups
Topic: Floyd Rose’s noiseless springs
Replies: 7
Views: 449

Floyd Rose’s noiseless springs

Have any of y’all used the noiseless springs on your Floyd rose tremelo system and noticed a difference in sound and quality of sound? They claim these noiseless springs take all the spring noise out of your tremelo system and give your guitar a crisp, clean sound. Well I bought a set of the standar...
by Jshannon3
Sat Jan 26, 2019 11:20 pm
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: Can Pedal power supplies cause noise in the signal
Replies: 3
Views: 244

Can Pedal power supplies cause noise in the signal

Can you get noise in your guitar signal from a bad pedal power supply? I got this ringing noise in my signal, I've tried isolating all the pedals down to one, the noise seems to chase whatever is plugged in, i can isolate the pedal board completely and plug directly in and it goes away. I checked ea...
by Jshannon3
Sat Jan 26, 2019 1:08 pm
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loop
Replies: 5
Views: 294

Re: U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loo

Update: I downloaded the signal diagram for the JVM410H, and man that clears a lot of things up, about why certain pedals don’t work in the loop. The signal already has distortion in it, so that would throw many pedals off especially if their looking for a clean signal. I know my Laney amplifier was...
by Jshannon3
Sat Jan 26, 2019 12:37 pm
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: Signal diagram for JVM410H
Replies: 1
Views: 145

Re: Signal diagram for JVM410H

Update: I found the signal diagram for a JVM410H online, I would post it here but for some reason I get an error code, but all you have to do is google”signal diagram for a JVM410H “ and you will get several hits on it.
by Jshannon3
Sat Jan 26, 2019 11:51 am
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: Signal diagram for JVM410H
Replies: 1
Views: 145

Signal diagram for JVM410H

Does anyone out the have a signal diagram for a JVM410H, that shows the signal path through the amp?
by Jshannon3
Sat Jan 26, 2019 11:45 am
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loop
Replies: 5
Views: 294

Re: U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loo

So what your saying is that I have a pre pre amp pedal board and an Post pre amp pedal board, their all in the same signal chain, I guess calling it 2 pedal boards is stretching it a bit,it’s like having one big pedal board split in half, a pre and a post, but some of my effects need the placement I...
by Jshannon3
Sat Jan 26, 2019 6:21 am
Forum: Effects, Pedals, JVM Loops, XLR Out, Line Out, Stereo Setup, Midi
Topic: U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loop
Replies: 5
Views: 294

U have too have 2 pedal boards with the JVM410H, one going in the front input of the amp, and one running the FX loop

Experimenting with the JVM410H, I’ve come to the conclusion the you need two effect pedal boards for your effects. I have one pedal board that is out front of the amp, coming off the guitar with a cord into this pedal board, through the effects, then cord goes to input of the amp. I call this the fr...